Turning the power on/off
Using batteries
17
Using batteries
Batteries that can be used
Use six AA nickel-metal hydride batteries or alkaline
batteries. Zinc-carbon batteries cannot be used.
Note: Batteries are not included. You’ll need to obtain them
separately.
Do not mix new and old batteries, or batteries of
differing types. Mixing batteries in this way may cause
them to leak or burst.
Continuous operating time
Alkaline batteries will allow approximately four hours of
usage. Battery life will depend on the type of batteries and
the conditions of use.
Replacing the batteries
An indicator on the upper right side of the screen shows the
remaining
battery capacity
( , , ).
If
you’re
using the AC adapter, this will indicate
.
If
is flashing, the batteries are almost exhausted.
Immediately save any important data, and either install
fresh batteries or switch to using the AC adapter.
If the batteries are exhausted, remove them
immediately. Leaving exhausted batteries installed may
cause malfunctions such as battery leakage. You should
also remove the batteries if you won’t be using the unit
for an extended period of time.
Note: If the batteries run low, you can plug in the AC
adapter and continue operation without having to power-off.
Turning the power on
1. Remove the battery compartment cover.
The
battery compartment of the KROSS-61 is located on
the bottom panel.
When turning the unit upside down, place it on a
blanket or similar material to prevent damage to the
knobs and dials.
While pressing the
cover latch, pull it
upward and
remove it.
KROSS-88: While
pressing from above
the ▲ on the cover,
slide it away from
yourself and remove.
Note: The battery
compartment
cover is
located on the left
side of the front
panel.
2. Install batteries.
When inserting the batteries, be sure to observe the
correct polarity (“+” and “–”). Place the “–” end of each
battery against the tip of the spring, and press it into
place.
KROSS-61
KROSS-88
3. Close the battery compartment cover.
Close the cover by reversing the steps you took to remove
it.
In order for the remaining battery amount to be
displayed correctly, you must set the Global/Media
mode GLOBAL> PREF page Battery Type setting to
specify the type of battery that you’re using.
Specifying the type of batteries you installed
After you’ve
installed the batteries, turn on the power and
specify the type of batteries you’re using.
1. In the GLOBAL> PREF (Preferences) page, select the
Battery Type parameter.
Perform steps 1–3 of “Changing the auto power-off
setting” on page 16.
2. Press the ENTER button to switch the setting.
Alkaline batteries: Alkaline
Nickel-metal hydride batteries: Ni-MH
3. Save the setting.
Press the FUNCTION button, and in the function list
choose Write Global Setting. (If a different function is
selected, press the PAGE– button to select it.)
Press the OK (MENU) button. A confirmation message
will appear; press the OK (MENU) button once again.
The setting has now been saved.
Setup
18
Connections
Connections must be made with the power turned off.
Please be aware that careless usage may damage your speaker system or cause other malfunctions.
Audio connections
Connecting your output devices
The KROSS does not contain built-in speakers. In
order to
hear the sound of your performance, you’ll need to connect
other audio equipment such as a monitor amplifier, a mixer,
a stereo set or headphones.
Connecting audio equipment
The KROSS’s audio output is designed to produce a
signal level that is higher than consumer audio
equipment such as CD players. For this reason,
performing at high a volume may damage your speakers
or equipment. Please use caution when adjusting the
volume.
1. Minimize the volume of all connected equipment, and
turn off the power.
2. Connect the KROSS’s OUTPUT L/MONO and R
jacks to the input jacks of your monitor amplifier or
mixer.
Note: If you connect only the L/MONO jack, the L and R
sound will be mixed for monaural output.
In order to take
full advantage of the KROSS’s capabilities, we
recommend that you listen in stereo.
If you’re playing back through your stereo audio system
or a cassette-radio that has external input connectors,
connect the KROSS to the jacks that are marked LINE
IN, AUX IN, or external input. (You might need to obtain
the appropriate adapter plug or conversion cable.)
Connecting headphones
Using headphones at high volume for an extended time
may cause hearing damage. Please avoid excessively
high volume levels.
1. Connect the stereo mini-plug
of your headphones to the
KROSS’s Headphone jack.
2. Use the VOLUME knob to
adjust the headphone
volume.
The KROSS’s Headphone jack
will output the same signal as
the OUTPUT L/MONO and R
jacks.
The output from the OUTPUT jack is not turned off even
if headphones are connected to the Headphone jack.
Connecting your input devices
You can sing while applying the built-in effects of the
KROSS to your mic, or connect an audio player and perform
along with the playback.
You can also use the audio recorder to record the audio
input.
If you’re not using the MIC IN or LINE IN jacks, turn
the AUDIO IN button off (unlit).
Connecting a mic
1. Make sure that the AUDIO IN button is off (unlit).
2. Turn the VOLUME knob of the KROSS all the way to
the left, minimizing the volume.
3. Connect a dynamic mic to the MIC IN jack.
Note: This jack does not support condenser mics or other
mics that require phantom power or plug-in power. Such
types of mic must be connected via a mic amp.
4. Turn the AUDIO IN button on (lit) to enable the
input.
5. While vocalizing into the mic and playing the
keyboard of the KROSS, slowly turn the VOLUME
knob toward the right until both are at the
appropriate volume.
The volume of the mic may differ depending on the
effect settings of the program or combination that’s
selected.
Pedal connections etc.
Connections to MIDI equipment
Connections to computers
Insert an SD card
Connect
output devices
Connect input devices
SD card slot
AUDIO OUTPUT
R, L/MONO
ASSIGNABLE
DAMPER, SWITCH, PEDAL
LINE IN, MIC IN
USB B
MIDI OUT, IN
AC adapter
(Included)
DC plug
to an
AC outlet
DS-1H
EXP-2, XVP-10
PS-1, PS-3
SD card
MIDI keyboard
MIDI IN
MIDI OUT
MIDI cable
USB cable
Computer
Audio player, etc.
Mic
Monitor Amplifier, etc.
INPUT
Headphones
