Microsoft Word e series interface setup instructions3 docx



Yüklə 1,38 Mb.
Pdf görüntüsü
tarix05.10.2018
ölçüsü1,38 Mb.
#72509


 

 

 



 

 

 



 

 

 



SATO Network Interface Card  

Configuration Instructions 

 

 

 



 

 

 



 

 

 



 

 



 

                     

SATO Network Interface Card Configuration Instructions   |   Rev A

 

 



 

 

www.satoamerica.com



 

2  


 

                                                                                 

Table of Contents 

 

1. Reset of wired/wireless interface card  ......................................................................  3  



2. Installing the All-In-One Utility (recommended)  .....................................................  4  

3. Configuring wired/wireless Ethernet with All-In-One Utility  ...............................  5  

           

A. Direct connection with cross-over cable  .............................................................  5  

           

B. Connection over a network.  .................................................................................  10  

           

C. Connection through a switch or hub.  ................................................................  12  

           

D. Setting up wireless configuration.  .....................................................................  16  

4. Installing the Admin Manager (legacy Ethernet installation utility)  .................  18  

5. Configuring wired/wireless Ethernet with Admin Manager  ..............................  20  

         

A. Direct connection with cross-over cable  ............................................................  20  

         

B. Connection over a network.  ..................................................................................  25  

         

C. Connection through a switch or hub.  .................................................................  27  

         

D. Setting up a wireless configuration.  ...................................................................  31  

 

 

 




 

                     

SATO Network Interface Card Configuration Instructions   |   Rev A

 

 



 

 

www.satoamerica.com



 

3  


1. Reset of wired/wireless interface card 

 

a)  Power off the printer and remove the top and bottom screw holding the interface card in 



place on the back of the printer. Pull the interface card out of the printer.

 

 



b)  On the interface card, look for 4 small dip switches. 

Turn dip switch number 2 on (away from the number), 

then reinstall the interface card on the back of the 

printer. Do not screw the top and bottom screws back 

in yet. 

c)  Power the printer on and wait for about 30 seconds. 

Power off the printer and pull the interface card back 

out.  Turn dip switch number 2 on the interface card 

back down and re-insert the card into the printer. Put 

the top and bottom screw back into the printer that holds the interface card in place. 

(*** Note: The pictures below show our current Network Interface cards which are only 

compatible with “e” series printers.  If you have a non “e” series printer they will not 

work. )  

 

 



 

 



 

                     

SATO Network Interface Card Configuration Instructions   |   Rev A

 

 



 

 

www.satoamerica.com



 

4  


2. Installing the All-In-One Utility (recommended) 

 

a)  Go to 



 www.satoamerica.com

 

b)  On the left side of the main page click the  “Resource Library” tab. Click on “All-In-One 



Printer Utility” in the expanded section heading. 

c)  Click on “Download the All-In-One Software”.  (Please make sure to have .NET 

FRAMEWORK 2.0 or higher on the computer. There is a link on this page to download 

and install it). 

d)  When prompted to open or save the file for download, make sure to save the file to the 

computer’s desktop or designated download folder. 

e)  When the file is finished downloading,  navigate to the folder the file was 

downloaded/saved to – right-click on downloaded filename and and click “Extract All…” 

from the quick pick menu.  Keep the directory as the default to unzip the file to the 

desktop.  (If you are using Windows 7 and have a prompt asking if you would like to 

copy this file without encryption, choose “yes”.) 

f)  Once files have been extracted, open the folder to view installation files. 

g)  Next double-click on setup.exe.  Follow the on-screen instructions to install the 

application. 

 

 



 

                     

SATO Network Interface Card Configuration Instructions   |   Rev A

 

 



 

 

www.satoamerica.com



 

5  


3. Configuring wired/wireless Ethernet with All-In-One Utility

 

 



a)  If the card has been previously configured or you would like to start from scratch to 

configure the card, follow the “Reset of wired/wireless interface card” procedure on 

page 3 before continuing. 

b)  There are three different methods for configuring a wired Ethernet interface card for a 

SATO printer. (A) Connection direct from PC/laptop to printer with a cross over cable. 

(B) Connection over a network.  (C) Connection through a switch or hub. 

 

A. Direct connection with cross-over cable 



(1)  Be sure to have a cross over cable accessible. The difference in a regular 

Ethernet cable and a cross over cable is how the end of the cable is wired.  

 

 

 



(2)  Connect one end of the cross over cable to the PC or Laptop and the other end 

to the back of the printer.  (Do not turn the printer on yet). 

 

 



 

                     

SATO Network Interface Card Configuration Instructions   |   Rev A

 

 



 

 

www.satoamerica.com



 

6  


(3)  The next couple steps will describe configuration of the computer for a static IP 

address; these steps are based on Windows XP; if you have Windows Vista or 

Windows 7 you can still change the same settings, but the process to do so is 

different. 

(4)  Click on “Start”. 

 

 



(5)  Click “Control Panel”.  (If “Control Panel” is not shown, click 

“Settings” and then “Control Panel”.  

 

 

(6)  Double click on “Network Connections”. 



 

 

 



 

(7)  Right click on 

“Local Area 

Connection” and 

then click 

“Properties”. 

 

 

 



 

 

 



(8)  Scroll down the list 

of connections and 

click on “Internet 

Protocol (TCP/IP)” 

and then click 

“Properties”. 

 

 



 

                     

SATO Network Interface Card Configuration Instructions   |   Rev A

 

 



 

 

www.satoamerica.com



 

7  


(9)  Chose the option 

for “Use the 

following IP 

address:” and 

assign the 

computer with an IP 

address within the 

same range of what 

you want to assign 

to the printer. For 

example, if you are 

setting the printer 

to 192.168.1.126 

you will want to use 

an IP address that 

has the last octet 

off by one number like in the picture to the right. The subnet mask will be based 

upon your IP address. If you need a list of appropriate subnet masks based upon 

your IP address you may need to consult your IT department or look up what 

subnet mask you need to have based upon your IP address on the internet. 

 

 

(10) After clicking ok from 



configuring the IP address 

and subnet mask, on the 

previous window click on 

“Install”. 

 

 

 



 

 

(11) Next, click on “Protocol” and 



then click “Add”. 

 

 



 

 



 

                     

SATO Network Interface Card Configuration Instructions   |   Rev A

 

 



 

 

www.satoamerica.com



 

8  


(12) Select the 

protocol 

listed as 

“IPX/SPX” 

and then 

click “OK”. 

(Windows 

Vista and 

Windows 7 

does not 

have this protocol so you can skip this step.) 

 

(13) You can now close all the open windows and turn the printer on.  Next, open the 



ALL IN ONE Application (Click “Start”, “All Programs”, “SATO”, and then 

“SATO All-In-One Application”).  Once open click the shortcut key for “IP 

Assignment tool”. (Shortcut key indicated by the red box).  

 

(14) The IP Assignment tool will automatically scan the network for the printer.  The 



list below shows 2 printers on a network, however your list should only show 1 

printer with an IP address of 0.0.0.0.  Click on your printer in the list and then 

click “Assign IP”.  (If you do not see anything in the list make sure you do not 

have any antivirus packages that include a firewall, if you do, please disable it. 

Also, if you are using Windows 7, you will have to disable the windows firewall).  

 

 



 


 

                     

SATO Network Interface Card Configuration Instructions   |   Rev A

 

 



 

 

www.satoamerica.com



 

9  


(15) On the next screen uncheck “DHCP” 

and “RARP” and then assign your IP 

address, subnet mask and default 

gateway. If you are unsure of what to 

assign, contact your IT department. 

After changing the appropriate 

settings, click “Apply” at the 

bottom. 


 

 

 



 

 

 



 

 

 



 

(16) A success message will 

pop up. Click “Yes” to 

reboot the interface.  

 

 

 



(17) Click “OK” on the next screen.  After clicking ok, wait about 1 minute and then 

continue to click the “Refresh” button on the previous window until you see the 

IP address that you just set on the printer. 

(18) Your printer is now set up properly.  If you are keeping the computer hooked up 

permanently this way, you will need to install the printer driver and labeling 

software package to start printing.  If the printer is being put on a network, 

power off the printer and use a regular Ethernet cable to connect the printer to 

the network. 

 

 

 




 

                     

SATO Network Interface Card Configuration Instructions   |   Rev A

 

 



 

 

www.satoamerica.com



 

10  


B. Connection over a network.

 

 



(1)  Before starting this configuration over a network please be aware that different 

networks are set up with different levels of security.  If this process fails, please 

revert to Section A (Direct connection with cross-over cable) to eliminate the 

possibility of the security on the network causing issues with set up of the 

interface card. 

(2)  If the card has been previously configured or you would like to start from scratch 

to configure the card, follow the “Reset of wired/wireless interface card” 

procedure on page 3 before continuing. 

(3)  Make sure to have a regular Ethernet cable hooked up from the network to the 

printer and power on the printer.  Your computer will also need to be connected 

to the same network as the printer. 

(4)  Open the ALL IN ONE Application (Click “Start”, “All Programs”, “SATO”, and 

then “SATO All-In-One Application”).  Once open click the  

shortcut key for “IP Assignment tool”.  

 

(5)  The IP Assignment tool will automatically scan the network for the printer. The 



list below shows 2 printers on a network.  Click on the printer in the list and then 

click “Assign IP” to set a static address to it.  If you want to keep the network 

card on DHCP then just record the IP address to set it up in the printer driver.  

 

 



 

 

 



 


 

                     

SATO Network Interface Card Configuration Instructions   |   Rev A

 

 



 

 

www.satoamerica.com



 

11  


(6)  On the next screen uncheck “DHCP” 

and “RARP” and then assign the IP 

address, subnet mask and default 

gateway. If you are unsure of what to 

assign, contact your IT department. 

After changing the appropriate 

settings, click “Apply” at the bottom. 

 

 



 

 

 



 

 

(7)  A success message will 



pop up. Click “Yes” to 

reboot the interface.  

 

 

 



 

(8)  Click “OK” on the next screen.  After clicking ok, wait about 1 minute and then 

continue to click the “Refresh” button on the previous window until you see the 

IP address just set on the printer. 

(9)  Your printer is now set up properly.  Now you will need to install the appropriate 

printer driver and labeling software. 

 



 

                     

SATO Network Interface Card Configuration Instructions   |   Rev A

 

 



 

 

www.satoamerica.com



 

12  


C. Connection through a switch or hub.

 

 



(1)  If the card has been previously configured or you would like to start from scratch 

to configure the card, follow the “Reset of wired/wireless interface card” 

procedure on page 3 before continuing. 

(2)  A switch, hub, or router is needed as well as 2 regular Ethernet cables.  Hook 

one Ethernet cable from the hub/switch to the printer, and another Ethernet 

cable from a different port in the hub/switch to the PC. 

(3)  The next couple steps will describe configuration of the computer for a static IP 

address; these steps are based on Windows XP; if you have Windows Vista or 

Windows 7 you can still change the same settings, but the process to do so is 

different.  

(4)  Click on “Start”.

 

 



(5)  Click “Control Panel”.  (If “Control Panel” is not shown, click “Settings” and then 

“Control Panel”.   

 

 

(6)  Double click on “Network Connections”. 



 

 

 



 

(7)  Right click on 

“Local Area 

Connection” and 

then click 

“Properties”. 

 

 

 



 

 

 



(8)  Scroll down the list 

of connections and 

click on “Internet 

Protocol (TCP/IP)” 

and then click 

“Properties”. 

 

 



 

                     

SATO Network Interface Card Configuration Instructions   |   Rev A

 

 



 

 

www.satoamerica.com



 

13  


(9)  Chose the option 

for “Use the 

following IP 

address:” and 

assign the 

computer with an IP 

address within the 

same range of what 

you want to assign 

to the printer. For 

example, if you are 

setting the printer 

to 192.168.1.126 

you will want to use 

an IP address that 

has the last octet 

off by one number like in the picture to the right. The subnet mask will be based 

upon your IP address. If you need a list of appropriate subnet masks based upon 

the IP address you may need to consult your IT department or look up what 

subnet mask you need to have based upon the internet’s IP address. 

 

 

(10) After clicking ok from 



configuring the IP address 

and subnet mask, on the 

previous window click on 

“Install”. 

 

 

 



 

 

(11) Next, click on “Protocol” and 



then click “Add”. 

 

 



 

 



 

                     

SATO Network Interface Card Configuration Instructions   |   Rev A

 

 



 

 

www.satoamerica.com



 

14  


(12) Select the 

protocol 

listed as 

“IPX/SPX” 

and then 

click “OK”. 

(Windows 

Vista and 

Windows 7 

does not 

have this protocol so you can skip this step.) 

 

(13) Close all your open windows and power the printer on.  Next, open your ALL IN 



ONE Application (Click “Start”, “All Programs”, “SATO”, and then “SATO All-

In-One Application”).  Once open click the shortcut key for “IP Assignment 

tool”.  

 

(14)  The IP Assignment tool will automatically scan the network for the printer.  The 



list below shows 2 printers on a network, however your list should only show 1 

printer with an IP address of 0.0.0.0.  Click on your printer in the list and then 

click “Assign IP”.  (If you do not see anything in the list make sure you do not 

have any antivirus packages that include a firewall, if you do, please disable it. 

Also, if you are using Windows 7, you will have to disable the windows firewall). 

 

 



 

 

 




 

                     

SATO Network Interface Card Configuration Instructions   |   Rev A

 

 



 

 

www.satoamerica.com



 

15  


(15) On the next screen uncheck “DHCP” 

and “RARP” and then assign the IP 

address, subnet mask and default 

gateway. If you are unsure of what to 

assign, contact your IT department. 

After changing the appropriate 

settings, click “Apply” at the bottom. 

 

 



 

 

 



 

 

(16) A success message will 



pop up. Click “Yes” to 

reboot the interface.  

 

 

 



(17) Click “OK” on the next screen.  After clicking ok, wait about 1 minute and then 

continue to click the “Refresh” button on the previous window until you see the 

IP address that you just set on the printer. 

(18) Your printer is now set up properly.  If you are keeping the computer hooked up 

permanently this way, you will just need to install your printer driver and labeling 

software package to start printing.  If the printer is being put on a network, just 

turn the power on the printer off and use a regular Ethernet cable to connect the 

printer to your network. 

 

 

 




 

                     

SATO Network Interface Card Configuration Instructions   |   Rev A

 

 



 

 

www.satoamerica.com



 

16  


 

 

D. Setting up wireless configuration.



 

 

(1)  Before starting this section, make sure dip 



switch number 4 on the wireless Ethernet card 

is in the up position to have the wireless mode 

enabled for infrastructure. 

 

 



 

 

(2)  Follow one of the previous 3 methods above (Section A, B, or C) to establish 



communication through the wired portion of the Ethernet card before 

continuing to the next step. 

(3)  Open the All-In-One Utility and then select the “IP Assignment Tool”.  

 

(4)  Select the printer to set up wirelessly and click on “Assign IP”.  



 

 

 



 

(5)  Next, click on “Wireless Setting”. 

 

 

 




 

                     

SATO Network Interface Card Configuration Instructions   |   Rev A

 

 



 

 

www.satoamerica.com



 

17  


(6)  The SSID will be the 

wireless network name.  

Authentication 

designates the 

preference to leave the 

connection open, or 

secure with a password. 

If you do use a password 

you have the option of 

WEP, or WPA. After 

setting all of the 

appropriate information, 

click “Apply”. 

(7)  After the changes have been applied power the printer off, disconnect the 

Ethernet cable on the back and restart the printer. 

(8)  You should now be able to communicate with the printer wirelessly.  Make sure 

to install the appropriate printer drivers and labeling software to complete your 

setup. 


 

(**Note: If you would like to use the wireless card in Ad hoc mode, put dip 

switch number 4 on the interface card to the off position.) 

 

 



 


 

                     

SATO Network Interface Card Configuration Instructions   |   Rev A

 

 



 

 

www.satoamerica.com



 

18  


4. Installing the Admin Manager (legacy Ethernet installation utility)

 

 



a)  Go to 

 

http://www.satoamerica.com/resource-­‐library/software/utilities.aspx



 webpage.

 

b)  In the table, click “Admin Manager”.Once you click on the link to download the Admin 



Manager utility, select “Save” option to save the file to the specified folder location 

(desktop folder is  recommended). 

c)  Once the download is complete, right click on the file named “AdminMgrV230.zip” on 

the desktop and click “Extract All”.  You can leave the default location on the extraction 

wizard to extract the file to your desktop.  (If you are using Windows 7 and are prompted 

if you would like to copy files without encryption, choose “yes”). 

d)  Look for the new folder created on the desktop named “AdminMgrV230” without a 

zipper on it and double click on this folder. 

 

e)  Double click on the “V230” folder, then double click on 



“Autorun.exe” 

 

 



f)  On the next screen click on “Setup”.

  

 



 

g)  Next click on “Advanced Setup”. 

 

 



 

                     

SATO Network Interface Card Configuration Instructions   |   Rev A

 

 



 

 

www.satoamerica.com



 

19  


i)  When prompted for another 

installation choice ,   use 

“Installing Admin Manager in 

your PC”. 

 

 

 



j)  Accept the license agreement on the next page and keep the file directory 

on the default directory and click “Next”.  Follow the next couple pages to 

finish the installation process. 

k)  The last step will ask to activate admin manager.  If yes is selected, the program will 

automatically open, if no is selected, the installation will be complete. 

 

 




 

                     

SATO Network Interface Card Configuration Instructions   |   Rev A

 

 



 

 

www.satoamerica.com



 

20  


5. Configuring wired/wireless Ethernet with Admin Manager

 

 



a)  If the card has been previously configured or you would like to start from scratch to 

configure the card, follow the “Reset of wired/wireless interface card” procedure on 

page 3 before continuing. 

b)  There are three different methods for configuring a wired Ethernet interface card for 

SATO printers. (A) Connection direct from PC/laptop to printer with a cross over cable. 

(B) Connection over a network.  (C) Connection through a switch or hub. 

 

A. Direct connection with cross-over cable



 

 

(1)  Make sure to have a cross over cable available. The difference in a regular 



Ethernet cable and a cross over cable is how the end of the cable is wired.  

 

 



 

(2)  Connect one end of the cross over cable to the PC or Laptop and the other end 

in the back of the printer.  (Do not turn the printer on yet). 

 

 




 

                     

SATO Network Interface Card Configuration Instructions   |   Rev A

 

 



 

 

www.satoamerica.com



 

21  


(3)  The next couple steps will describe configuration of the computer for a static IP 

address; these steps are based on Windows XP; if you have Windows Vista or 

Windows 7 you can still change the same settings, but the process to do so is 

different. 

(4)  Click on “Start”.

 

 



(5)  Click “Control Panel”.  (If “Control Panel” is not shown, click 

“Settings” and then “Control Panel”.  

 

 

(6)  Double click on “Network Connections”. 



 

 

 



 

(7)  Right click on 

“Local Area 

Connection” and 

then click 

“Properties”. 

 

 

 



 

 

 



(8)  Scroll down the list 

of connections and 

click on “Internet 

Protocol (TCP/IP)” 

and then click 

“Properties”. 

 

 



 

                     

SATO Network Interface Card Configuration Instructions   |   Rev A

 

 



 

 

www.satoamerica.com



 

22  


(9)  Chose the option 

for “Use the 

following IP 

address:” and 

assign the 

computer with an IP 

address within the 

same range of what 

you want to assign 

to the printer. For 

example, if you are 

setting your printer 

to 192.168.1.126 

you will want to use 

an IP address that 

has the last octet 

off by one number like in the picture to the right. The subnet mask will be based 

upon your IP address. If you need a list of appropriate subnet masks based upon 

your IP address you may need to consult your IT department or look up what 

subnet mask you need to have based upon your IP address on the internet. 

 

 

(10) After clicking ok from 



configuring the IP address 

and subnet mask, on the 

previous window click on 

“Install”. 

 

 

 



 

 

(11) Next, click on “Protocol” and 



then click “Add”. 

 

 



 

 

 




 

                     

SATO Network Interface Card Configuration Instructions   |   Rev A

 

 



 

 

www.satoamerica.com



 

23  


(12) Select the 

protocol 

listed as 

“IPX/SPX” 

and then 

click “OK”. 

(Windows 

Vista and 

Windows 7 

does not 

have this protocol so you can skip this step.) 

(13) Close all of the open windows and power on the printer. Open the Admin 

Manager program. Admin Manager will automatically scan the printer when the 

program opens. In the list there is only one printer with the IP address “0.0.0.0” 

and an Ethernet address next to it. (If you do not see anything in the list, make 

sure to disable any antivirus packages including firewalls. Also, in Windows 7, 

the Windows firewall must be disabled.)  

 

(14) Right click on your printer in the list and click “Configuration via web browser”. 



You will then be prompted to assign an IP address to the printer. After 

assigning an IP address, you will get confirmation.  

 

 

 




 

                     

SATO Network Interface Card Configuration Instructions   |   Rev A

 

 



 

 

www.satoamerica.com



 

24  


(15) Close Admin Manager and 

open Internet Explorer. Go to 

the address bar at the top 

and type the IP address just 

assigned to the printer. You 

will be routed to a page as 

shown to the right. 

 

 



(16) On the left side of the screen, under “Server Configuration” click on “Print 

Server”. You will be prompted to input a username and password. The 

username is “root” and the password is “” (no password). 

 

(17) At the top of the screen you will see an option for 



“TCP/IP”.  After clicking on this tab you can disable 

DHCP, and set your IP Address, Subnet Mask, and 

Default Gateway.  When finished, click the “Submit” 

button at the bottom and you should see “Accepted” to 

let you know the changes were successful.  

 

(18) Your printer is now set up properly.  If you are keeping the computer hooked up 



permanently this way, you will just need to install your printer driver and labeling 

software package to start printing.  If the printer is being put on a network, just 

turn the power on the printer off and use a regular Ethernet cable to connect the 

printer to your network. 

 

 

 




 

                     

SATO Network Interface Card Configuration Instructions   |   Rev A

 

 



 

 

www.satoamerica.com



 

25  


B. Connection over a network.

 

 



(1)  Before starting this configuration over a network please be aware that different 

networks are setup with different levels of security. If this process fails, please 

revert to Section A (Direct connection with cross-over cable) to eliminate the 

possibility of the security on the network causing issues with setup of the 

interface card. 

(2)  If the card has been previously configured or you would like to start from scratch 

to configure the card, follow the “Reset of wired/wireless interface card” 

procedure on page 3 before continuing. 

(3)  Make sure to have a regular Ethernet cable hooked up from the network to the 

printer and power on the printer.  The computer will also need to be connected 

to the same network as the printer. 

(4)  Open the Admin Manager application (Click “Start”, “All Programs”, “Admin 

Manager”). The program will automatically scan the network for any SATO 

network interface cards. Once you see the appropriate printer, right click on it 

and click “Configuration via web browser” to set a static address to it. If the card 

needs to stay on DHCP, record the IP address and set it up in the printer driver 

at a later time.  

 

 



 


 

                     

SATO Network Interface Card Configuration Instructions   |   Rev A

 

 



 

 

www.satoamerica.com



 

26  


(5)  Close Admin 

Manager and open 

Internet Explorer. Go 

to the address bar at 

the top and type the 

IP address just 

assigned to the 

printer. You will be 

routed to a page as 

shown to the right. 

(6)  On the left side of the screen, under “Server 

Configuration” click on “Print Server”. You will be 

prompted to input a username and password.

 

 The 



username is “root” and the password is “” (no 

password).  

(7)  At the top of the screen you will see an option for 

“TCP/IP”.  After clicking on this tab you can disable DHCP, and set your IP 

Address, Subnet Mask, and Default Gateway.  When finished, click the “Submit” 

button at the bottom and you should see “Accepted” to let you know the 

changes were successful.  

 

(8)  Your printer is now setup properly. You will need to install the appropriate 



printer driver and software package to begin printing. 

 

 



 


 

                     

SATO Network Interface Card Configuration Instructions   |   Rev A

 

 



 

 

www.satoamerica.com



 

27  


C. Connection through a switch or hub.

 

 



(1)  If the card has been previously configured or you would like to start from scratch 

to configure the card, follow the “Reset of wired/wireless interface card” 

procedure on page 3 before continuing. 

(2)  You will need to have a switch, hub, or router to act as a switch as well as 2 

regular Ethernet cables.  Hook one Ethernet cable from your hub/switch to your 

printer, and another Ethernet cable from a different port in your hub/switch to 

your PC. 

(3)  The next couple steps will describe configuration of the computer for a static IP 

address; these steps are based on Windows XP; if you have Windows Vista or 

Windows 7 you can still change the same settings, but the process to do so is 

different. 

(4)  Click on “Start”.

  

 

(5)  Click “Control Panel”.  (If “Control Panel” is not shown, click “Settings” and then 



“Control Panel”.  

 

 



(6)  Double click on “Network Connections”. 

 

 



 

 

(7)  Right click on 



“Local Area 

Connection” and 

then click 

“Properties”. 

 

 

 



 

 

 



(8)  Scroll down the list 

of connections and 

click on “Internet 

Protocol (TCP/IP)” 

and then click 

“Properties”. 

 

 



 

                     

SATO Network Interface Card Configuration Instructions   |   Rev A

 

 



 

 

www.satoamerica.com



 

28  


(9)  Chose the option 

for “Use the 

following IP 

address:” and 

assign the 

computer with an IP 

address within the 

same range of what 

you want to assign 

to the printer. For 

example, if you are 

setting your printer 

to 192.168.1.126 

you will want to use 

an IP address that 

has the last octet 

off by one number like in the picture to the right. The subnet mask will be based 

upon your IP address. If you need a list of appropriate subnet masks based upon 

your IP address you may need to consult your IT department or look up what 

subnet mask you need to have based upon your IP address on the internet. 

 

 

(10) After clicking ok from 



configuring the IP address 

and subnet mask, on the 

previous window click on 

“Install”. 

 

 

 



 

 

(11) Next, click on “Protocol” and 



then click “Add”. 

 

 



 

 

 



 

 

 




 

                     

SATO Network Interface Card Configuration Instructions   |   Rev A

 

 



 

 

www.satoamerica.com



 

29  


(12) Select the 

protocol 

listed as 

“IPX/SPX” 

and then 

click “OK”. 

(Windows 

Vista and 

Windows 7 

does not 

have this protocol so you can skip this step.) 

(13) Close all open windows and power on the printer. Open the Admin Manager 

program. Admin Manager will automatically scan the printer when the program 

opens. In the list there is only one printer with the IP address “0.0.0.0” and an 

Ethernet address next to it. (If you do not see anything in the list, make sure to 

disable any antivirus packages including firewalls. Also, in Windows 7, the 

Windows firewall must be disabled.)  

 

(14) Right click on your printer in the list and click “Configuration via web browser”. 



You will then be prompted to assign an IP address to the printer. After 

assigning an IP address, you will get confirmation.  

 

 

 




 

                     

SATO Network Interface Card Configuration Instructions   |   Rev A

 

 



 

 

www.satoamerica.com



 

30  


(15) Close Admin Manager 

and open Internet 

Explorer. Go to the 

address bar at the top 

and type the IP address 

just assigned to the 

printer. You will be 

routed to a page as 

shown to the right. 

(16) On the left side of the screen, under “Server Configuration” you will want to 

click on “Print Server”. You will be prompted to input a username and 

password. The username is “root” and the password is “” (no password). 

(17) At the top of the screen you will see an option for “TCP/IP”.  After clicking on 

this tab you can disable DHCP, and set your IP Address, 

Subnet Mask, and Default Gateway.  When finished, 

click the “Submit” button at the bottom and you should 

see “Accepted” to let you know the changes were 

successful.  

 

(18) Your printer is now setup properly. If you are keeping the computer hooked up 



permanently this way, you will need to install the printer driver and labeling 

software package to start printing. If the printer is being put on a network, turn 

the power off and use a regular Ethernet cable to connect the printer to the 

network. 

 

 



 

                     

SATO Network Interface Card Configuration Instructions   |   Rev A

 

 



 

 

www.satoamerica.com



 

31  


 

 

D. Setting up a wireless configuration.



 

 

(1)  Before starting this section, make sure 



dip switch number 4 on the wireless 

Ethernet card is in the up position to 

have the wireless mode enabled for 

infrastructure. 

(2)  Follow one of the previous 3 methods 

above (Section A, B, or C) to establish 

communication through the wired 

portion of the Ethernet card before continuing to the next step. 

(3)  Open the Admin Manager application (Click “Start”, “All Programs”, “Admin 

Manager”). The program will automatically scan the network for any SATO 

network interface cards. Once you see the appropriate printer, right click on it 

and click “Configuration via web browser” to set a static address to it. If the card 

needs to stay on DHCP, record the IP address and set it up in the printer driver 

at a later time.  

 

(4)  Close Admin Manager and open Internet Explorer. Go to the address bar at the 



top and type the IP 

address just assigned 

to the printer. You 

will be routed to a 

page as shown to the 

right. 


 

 



 

                     

SATO Network Interface Card Configuration Instructions   |   Rev A

 

 



 

 

www.satoamerica.com



 

32  


(5)  On the left side of the screen, under “Server 

Configuration” you will want to click on “Print 

Server”. You will be prompted to input a 

username and password. The username is “root” 

and the password is “” (no password).

  

 



(6)  At the top of the screen you will see an option for “TCP/IP”.  After clicking on 

this tab you can disable DHCP, and set your IP Address, Subnet Mask, and 

Default Gateway.  When finished, click the “Submit” button at the bottom and 

you should see “Accepted” to let you know the changes were successful.  

 

(7)  Next click on the “Wireless” tab at the top and assign your “”SSID” name for 



your wireless network.  

 

(8)  Further down on this same page you will see options for WEP security and for 



WPA security. If you are using WEP, change the drop down box to “Enable” and 

select your appropriate key number and password (this would be provided by 

your IT staff). If you are using WPA security, change (Network Authentication) at 

the top of the page to “WPA” and then scroll down the page until you reach 

“WPA Config”. Choose “TKIP” or “AES” depending on what your IT 

department wants you to use, and enter your password next to “Pre-Shared 

Key”. If you are not using security at all, make sure “Network Authentication” 



 

                     

SATO Network Interface Card Configuration Instructions   |   Rev A

 

 



 

 

www.satoamerica.com



 

33  


stays on “Open System” and do not change any settings other than the SSID on 

this page. When the entire configuration is complete, click “Submit” at the 

bottom of the page and you will get an “Accepted” message. 

(9)  You will now need to power the printer off, unhook the Ethernet cable, and 

power the printer on. The printer is now setup for wireless printing. 

 

(**Note: If you would like to use the wireless card in Ad hoc mode, put dip 



switch number 4 on the interface card to the off position.) 

Yüklə 1,38 Mb.

Dostları ilə paylaş:




Verilənlər bazası müəlliflik hüququ ilə müdafiə olunur ©www.genderi.org 2024
rəhbərliyinə müraciət

    Ana səhifə